RVPW011-FJ1-CT

  • 5V~50V Ultra-wide Range of Input Voltage
  • Suitable for Primary Side Feedback Flyback Converter
  • Minimum Sampling Time as Low as 0.4uS
  • Boundary Conduction Mode at the Heavy Load
  • Decrease the Operating Frequency to Improve Efficiency Under Light-load Conditions
  • Integrated 90V/40mΩ LDMOS
  • Integrated Lossless Current Sampling
  • Programmable Peak Current
  • Programmable Power MOSFET Driving Speed
  • Programmable Feedforward Compensation
  • Programmable Soft Start
  • Programmable Input Undervoltage and Overvoltage Protection
  • Short Circuit Protection, and Over Temperature Protection
  • Internal Loop Compensation
  • Current Less Than 0.1μA When Enable Turn Off
  • Output Diode Voltage Drop Temperature Compensation
  • QFN5x5 Strong Heat Dissipation Packaging

RVPW011 is a flyback converter that achieves voltage regulation by sampling the primary winding of the transformer, supporting primary-side regulation (PSR) feedback at operating frequencies in the hundreds of kHz. Its internal output voltage sampling circuit operates with a sampling voltage pulse as narrow as 400ns. Equipped with an internal loop compensation circuit and fast dynamic response capability, the RVPW011 ensures excellent system stability and dynamic performance for switching power supplies. Designed for low-voltage operation, the RVPW011 supports input voltages as low as 5V. It features a low on-resistance internal MOSFET of just 40mΩ. Combined with its thermally efficient 5mm×5mm QFN package, the device can deliver output power up to 30W. RVPW011 integrates multiple control functions with minimal external components, allowing designers to tailor the system to specific application needs. It enables startup, feedforward compensation, and control over the shutdown speed of the internal power MOSFET via external resistors. The peak current of the power MOSFET can also be programmed using a resistor, enabling “lossless” current sensing. Input undervoltage and overvoltage protection thresholds can be set simultaneously using two resistors. Additionally, the soft-start time is programmable through an external capacitor, allowing for optimized performance based on the application. To ensure robust and reliable operation, the RVPW011 incorporates built-in protections including overload protection, output short-circuit protection, output overvoltage protection, and over-temperature protection. These protection mechanisms support automatic recovery after fault conditions are resolved, maximizing the reliability and resilience of the overall power supply system.

Solutions based on this IC/Transformer combination (available board mounted or as individual components)

  Part Number Power (W) Isolation (kV) Vin (V) Main Vout (V) Primary IC Transformer Secondary IC
1
New
6 6 16 - 32 2.5 to 4
Attributes RVPW011-FJ1-CT
Product Category IC
Vin (V) 5 - 50
Main Vout (V) 2 to 999
Output Voltage Range (V) 2 - 999
MAX Iout (mA) 10
Mounting Type SMD (pinless)
Package Style QFN5x5
Length (mm) 5.1
Width (mm) 5.1
Height (mm) 0.8
MIN Operating Temp (°C) -40
MAX Operating Temp (°C) 125
Protections OCP, OTP, OVP
Directives Halogen-free, REACH, RoHS 2+ (10/10)
Packaging Type Moisture Barrier Bag
Operating Modes Current Mode
Warranty 1 Year
Config 1 Channel
Topology Flyback
Number of Phases 1
Functional Features Enable, Soft Start, Variable Switching Frequency
MIN Switching Frequency (kHz) 9
MAX Switching Frequency (kHz) 330
MIN Storage Temperature (°C) -55
MAX Storage Temperature (°C) 150
Important parameters include input voltage range, output voltage, maximum load current, switching frequency, efficiency, size, and thermal performance. Selection involves balancing these factors to meet the specific requirements of your application, ensuring the IC operates within its safe thermal and electrical limits while minimizing PCB space.
A boost converter increases the input voltage to a higher output voltage using an inductor, low-side switch, a rectifier, and output filter.
A buck converter reduces the input voltage to a lower output voltage using a high-frequency high-side or low-side switch, an inductor, a rectifier, and output filtering.
A buck‑boost converter can both increase and decrease the output voltage in relation to the input voltage using one or more inductors, a high-side or a low-side switch, rectifiers, and output filtering.
A DC/DC controller IC manages the switching behavior of external power components such as MOSFETs, inductors, and transformers.
A DC/DC converter IC converts one DC voltage level to another using switching techniques and integrated control circuitry.
A synchronous converter replaces the traditional rectifier diode with a MOSFET, which reduces conduction losses and significantly improves efficiency.
An asynchronous converter uses a diode as the rectification element, resulting in a simpler design but typically lower efficiency compared to synchronous alternatives.
A converter IC typically integrates the power switches internally, providing a more compact solution. In contrast, a controller IC manages the switching behavior of external power components such as MOSFETs, inductors, and transformers.
Buck-boost converters are commonly used when the input voltage can vary above and below the desired output voltage. For example, this topology is ideal for maintaining a 12V fixed voltage from a 12V battery supply, where the battery level may fluctuate during discharge or charging.
Push-pull and full bridge topologies are often unregulated, making them best suited for use with regulated input voltage rails. Push-pull is preferred for 3.3V and 5V input voltage rails because the input current is shared between the switching transistors, allowing more power to be extracted from a smaller IC package. Full Bridge is preferred for 5V up to 24V input voltage rails because the input voltage stress is shared between the switching transistors, enabling it to efficiently switch higher input voltages. For regulated output voltages, wider input voltage ranges, or higher output power applications, Flyback is the preferred topology due to its versatility and ability to provide galvanic isolation.
Power ICs enable efficient switching topologies, optimized control algorithms, and fast switching frequencies that minimize power losses.
Key advantages include high integration, a small footprint, and improved efficiency. Integrated power ICs allow designers to create optimized power solutions tailored specifically for unique applications.
Power ICs typically require more external components and careful PCB design. This requirement for additional external parts and complex layout increases overall development complexity.
Common types include DC/DC converter ICs, PWM controller ICs, gate driver ICs, PMICs, linear regulators, and battery management ICs.
Power ICs are used in industrial electronics, telecom systems, consumer electronics, automotive systems, and IoT devices.
A power IC (power integrated circuit) is a semiconductor device designed to regulate or convert electrical power. It integrates essential functions such as feedback regulation, switching control, protection, and power management into a single chip.
A PMIC is an integrated circuit designed to manage power distribution within complex electronic systems. It typically integrates multiple voltage regulators, power sequencing, battery management, and system monitoring functions into a single semiconductor device.
A power IC is a semiconductor controller chip that requires external magnetic components such as inductors or transformers but often includes integrated power switching transistors. A power module integrates many of these discrete components into a single packaged solution, simplifying PCB design and reducing overall development time.
Power switching transistors differ primarily in how they are controlled, their switching speed, maximum switching voltage, and their power-handling limits. The main types include MOSFETs (up to 100kHz, 600V, 1kW), SiCs (up to 500kHz, 3.3kV, 100kW), GaNs (up to 1MHz, 900V, 10kW), and IGBTs (up to 50kHz, 6.5kV, 1MW).

MOSFETs are most often used in switching power supplies due to their low cost and ease of integration. SiCs and GaNs are utilized for high-frequency switching applications, while IGBTs are preferred for very high power or high-voltage switching.
Power ICs are often utilized when designers require maximum flexibility, lower cost at high volumes, or highly customized power architectures.

...お探しのものは見つかりませんでしたか？

パラメトリック検索を利用したり、カスタマイズされたソリューションに注目したり、お近くの販売窓口を探したりしてください。

パラメトリックサーチ

キーワード検索

検索

Customized Solution

Get your customized discrete solution.

Request now

オンライン注文

貴方の地域の営業拠点

コンタクト